Receiver Packs


     All NiMh RX packs voltage matched and hand assembled. These packs are soldered (not spot welded), cycled, and tested to ensure you get the best performance. They are also double shrink wrapped for added durability. With low internal resistance, these packs provide the most amount of current for you high torque servos without a drastic voltage drop.  

     The 2500mAh packs will provide over an hour of run time in most setups even with the highest torque servos available.  Your brakes will pull just as hard at the end of the race as in the beginning.  They can also be charged up to 1,000 times without a memory.  Equipped with 4" to 6" long universal receiver connector. 

The 1600mAh packs are for tighter applications, special battery boxes, or those racers who want the lightest car possible. Great for all applications there is a receiver pack below for your car or truck.


SRP2500-MUG

     The 2+2+1, or Mugen style is a 2500mAh 6v Nimh receiver pack that fits in the standard battery box on a number of popular 1/8 scale buggies and truggies. 

     Designed specifically for the MBX-5 this pack will fit Jammin X1CR, Team Associated RC8, Cen Matrix, Kyosho, Caster, and others. 

     Check the dimensions for your application. I have seen these zip tied into monster trucks and they drop right into the Nitro NTC3 on road cars as well.

A charge rate of 1 Amp is recommended for the best battery life.

  •  Length: 54mm (2.1")
  •  Width: 30 mm (1.2")
  •  Height: 43 mm (1.7")
  •  Weight 159 g. (5.6oz)

SRP2500-LOS


     The 3+2, or Losi style is a 2500mAh 6v Nimh receiver pack that fits in the standard battery box of the Losi 8ight and 8ight-T. 

     I admit its a tight fit but if you want this kind of run time and servo power its not that big a deal.  Just watch out for that screw that comes into the battery box and make sure its not too long or it will damage the cells. 

     I have also seen this pack installed in a MBX6 and XRAY 808 but the battery box was modified. Check the diminsions for your application. 

A charge rate of 1Amp is recommended for the best battery life.

  • Length: 54mm (2.1")
  • Width: 45mm (1.8")
  • Height: 30mm (1.2")
  • Weight: 159g (5.6oz)



SRP1600-FLT


     This flat pack uses 2/3A cells at 1600mAh and is designed for the Mugen MBX-6 and the X-Ray 808 buggys.  It will fit several other cars and trucks that take a flat pack. 

     These are matched and hand soldered .  This pack includes a 4 inch lead with a universal connector.  

A charge rate of 1 Amp is recommended for the best battery life.

  • Length: 84mm (3.3")
  • Width: 30mm (1.2")
  • Height: 17mm (0.7")
  • Weight: 125g (4.4oz)




SRP1600-HMP


     This hump pack uses 2/3A cells at 1600mAh and is designed for most 1/8 scale buggies that use hump packs.  It will fit  1/10 scale nitro cars and trucks as well and with 1600mAh is can handle high torque servos. 

     This pack features a 6 inch lead with universal connector.  These cells are matched, hand soldered and a 1 Amp charge rate is recommended for the best battery life.

  • Length: 51mm (2.0")
  • Width: 34mm (1.3")
  • Height: 32mm (1.2")
  • Weight: 125g (4.4oz)